Hi all,
I'm trying to get APRS positions from a Motorola R7 through my openSPOT4 on BrandMeister and the location exchange never completes. Voice works perfectly. I'd appreciate help understanding whether the openSPOT is handling DMR confirmed data correctly in this setup.
Setup
- openSPOT4, firmware v93 stable, Homebrew connector to BM master 3102, hotspot ID 312931601
- 433.650 MHz simplex, DMR, TS2, CC1
- AutoCal done today; R7 voice BER now about 0.1%
- APRS background connector disabled (it was enabled earlier; disabling it removed a separate retry storm)
- Radio: Motorola R7, ID 3129316, ARS to 310999 (port 4005), CAI 12/225, Compressed UDP header DMR Standard, IP Site Connect on, Data Call Confirmed on, TX Preamble 960 ms
- BM SelfCare for 3129316: Brand = Motorola, APRS callsign KD0TNH-7. The same ID posted to aprs.fi fine from an AnyTone radio, so the BM/APRS-IS side works for this ID.
What happens (from the openSPOT debug log)
- Radio sends CSBK preambles, then a short private data call to 310999 (ARS registration). Forwarded fine.
- BM immediately sends a 1-block reply; openSPOT transmits it (modem-tx start/end).
- BM then sends a 3-block confirmed data message (rate 3/4) to the radio.
- About 2 s later the radio sends a rate 1/2 data call to 310999. I believe this is the DMR confirmed-data response (ACK/NACK).
- BM resends the same 3-block message 3 more times (6 s apart), the radio answers each time, then BM gives up.
- About 80 s later the radio registers again and the cycle repeats. No position ever reaches APRS-IS.
Things that look odd to me in the log
- The radio's rate 1/2 responses always show 2-7% BER and a fixed -64 dBm, and end with "call ended (timeout)". Every other R7 transmission in the same log is 0% BER at -23 to -75 dBm.
- The radio's normal data calls are followed by "homebrew-dmr: [0] call stopped". The rate 1/2 responses are not, so I'm not sure they are being forwarded to BM.
Log excerpt (times CDT)
16:50:21 dmrct: [0] prv data call started, dst: 3129316 src: 310999 id: 67db0b51bca7aef0
16:50:21 dmr-sms: sms call is not ongoing, ignoring rate 3/4 data (x3)
16:50:22 modem-tx: start
16:50:22 modem-tx: end
16:50:23 dmrct: [0] prv data call started, dst: 310999 src: 3129316 id: 9b596427452c10e4
16:50:23 dmr-sms: sms call is not ongoing, ignoring rate 1/2 data
16:50:25 dmrct: [0] call ended (timeout), dur 4.1s ber 0.0% loss 0.0% rssi 0
16:50:26 dmrct: [0] call ended (timeout), dur 3.1s ber 2.3% loss 0.0% rssi -64
16:50:28 dmrct: [0] prv data call started, dst: 3129316 src: 310999 id: afd45d0cb677a47e
... (same pattern at 16:50:33 and 16:50:40)
Questions
- Does the openSPOT4 forward DMR confirmed-data response packets (rate 1/2) from the radio to a Homebrew master?
- Could simplex TX-to-RX turnaround be clipping the radio's response, given it comes back about 1-2 s after the openSPOT transmits?
- AutoCal improved the openSPOT's receive. Is the transmit side corrected by the same offset, or could a TX frequency error corrupt rate 3/4 data blocks while voice still sounds fine?
- Has anyone gotten Motorola MOTOTRBO ARS/LRRP positions working through an openSPOT on BrandMeister, and if so, with what settings?
I have the full debug log and call log CSVs if useful. I've also opened a ticket with BrandMeister support.
Thanks,
Jeff, KD0TNH