Search found 8 matches

by tony_b
Sat Jun 01, 2019 5:17 pm
Forum: Troubleshooting
Topic: FCS servers stop changing from FUSION radio
Replies: 12
Views: 665

Re: FCS servers stop changing from FUSION radio

That's the next step I was going to try. If the problem goes away, it's an issue with the other openSPOT1. If the problem moves to the 2nd openSPOT1, the problem becomes harder and is likely a local Internet issue. I won't be going back to AZ for some time, so, I'll add to this thread when I get bac...
by tony_b
Wed May 29, 2019 8:01 pm
Forum: Troubleshooting
Topic: FCS servers stop changing from FUSION radio
Replies: 12
Views: 665

Re: FCS servers stop changing from FUSION radio

My 2nd openSPOT 1 seems to not exhibit the problem I reported initially. After several days the FUSION FCS servers and rooms seem to continue to change just fine with *DTMF commands. Any ideas on what to check with my other openSPOT 1 on my home network in AZ ? The problem does seem to be consistent...
by tony_b
Thu May 23, 2019 2:46 pm
Forum: Troubleshooting
Topic: FCS servers stop changing from FUSION radio
Replies: 12
Views: 665

Re: FCS servers stop changing from FUSION radio

Thank you. I have to work away from home for a few days but have a second openSPOT1 with me on which I can see if the issue is consistent across both devices. It will take me a few days to get to this. I will get back to you likely next week and send you the configuration file if the problem is pres...
by tony_b
Sat May 18, 2019 10:53 pm
Forum: Troubleshooting
Topic: FCS servers stop changing from FUSION radio
Replies: 12
Views: 665

Re: FCS servers stop changing from FUSION radio

I never shut it down since I've loaded 141 firmware unless I need to physically relocate it. So, it's been up and on-line for months. I've only been on FUSION for about the last 3 weeks. For the first week I changed servers/rooms via the openSPOT's web interface because I used YSF reflectors. Then w...
by tony_b
Sat May 18, 2019 3:42 pm
Forum: Troubleshooting
Topic: FCS servers stop changing from FUSION radio
Replies: 12
Views: 665

Re: FCS servers stop changing from FUSION radio

Thank you. One more piece of data for you... It is now 0840 the following morning here in AZ. I just entered *285 to change from *290 to the new FCS FUSION server/room. The openSPOT 1 switched "channels" normally on the first try. So the problem occurs only with more like 24 hours or more of transmi...
by tony_b
Sat May 18, 2019 5:01 am
Forum: Troubleshooting
Topic: FCS servers stop changing from FUSION radio
Replies: 12
Views: 665

Re: FCS servers stop changing from FUSION radio

Nonoo: It has now been about 24 hours since my openSPOT 1's last manual reboot. I tried changing from FCS "290" (America-Link) to Ragchew "285" again tonight (Friday, 17 May; 2130 Arizona USA time) via the radio, by sending DTMF stream *285. Five "ignores" in a row occurred. Then another station cal...
by tony_b
Fri May 17, 2019 8:14 pm
Forum: Troubleshooting
Topic: FCS servers stop changing from FUSION radio
Replies: 12
Views: 665

Re: FCS servers stop changing from FUSION radio

Yes. All green LED's are solidly lit. The red one also shows any activity on the currently chosen "channel". I can communicate normally on this server/FCS FUSION room that is indicated as the current selection on the status tab of the openSPOT web interface. I simply can no longer change servers and...
by tony_b
Thu May 16, 2019 7:01 pm
Forum: Troubleshooting
Topic: FCS servers stop changing from FUSION radio
Replies: 12
Views: 665

FCS servers stop changing from FUSION radio

Equipment: Yaesu FT-70DR radio, openSPOT1 (running 141 firmware). Conditions: Initially set FCS FUSION mode and server/room from pc on home network. Everything works fine. FCS settings can easily be changed using "*srr" (asterisk, server single digit number, 2 digit room number) command from radio. ...